Electrician reviewing conduit and panel layout on a commercial job site
Back to Blog
Electrical Systems8 min read·October 5, 2026

Electrical Takeoff Checklist for Commercial Buildings

A reliable electrical takeoff checks every circuit against the panel schedule. That covers conduit, wire, devices, and gear, so nothing slips through.

An electrical takeoff is only as good as its cross-checking. Miss one circuit against the panel schedule and the gap shows up as a change order later.

This checklist covers every item a commercial electrical takeoff should capture. Use it before you submit a bid.

A quick answer: a complete electrical takeoff counts conduit, wire, panels, and devices by size and type. Every circuit then gets reconciled against the panel schedule before pricing.

Start Every Electrical Takeoff With the Panel Schedule

The panel schedule is the single source of truth for circuit count and breaker sizing. Every circuit on the floor plan should match a circuit on the schedule. If it does not, flag it before pricing.

This reconciliation step catches the most common drafting errors. A circuit on the plan but missing from the schedule is a frequent and costly miss.

Conduit and Wire Takeoff Checklist

Conduit and wire make up the bulk of electrical material cost on most commercial jobs. Break them out by type and size, not a blended average.

  • EMT, rigid, PVC, and flexible conduit, each taken off by size
  • Wire and cable footage by conductor size and insulation type
  • Homerun lengths measured from panel to first device, not estimated
  • Underground or concrete-encased conduit counted separately from above-ceiling runs

Panels, Gear, and Switchgear

Switchgear, switchboards, panelboards, and transformers each get their own line item. Note voltage, ampacity, and AIC rating for every piece of gear.

Gear pricing and lead time work differently than bulk material. Flag long-lead equipment, main switchboards especially, early in the takeoff. Procurement delays on gear can hold up an entire project schedule.

Device and Fixture Takeoff Checklist

Devices and fixtures need to be counted by type, not grouped into one generic tally. Labor units differ meaningfully between device types.

  1. 1Receptacles: standard duplex, GFCI, isolated ground, dedicated circuits
  2. 2Switches: single-pole, three-way, dimmers, occupancy sensors
  3. 3Lighting fixtures by type, mounting, and circuit assignment
  4. 4Emergency and exit lighting tied to life safety circuits

A project with many specialty circuits needs this level of detail. Treating every receptacle the same misprices labor fast.

Electrical Takeoff Pricing Factors

Electrical cost per square foot varies widely by building type and system complexity. These 2026 ranges apply to US commercial work.

  • Basic tenant improvement: $6 to $12 per sq ft
  • Standard commercial office or retail: $10 to $18 per sq ft
  • Healthcare or lab space with redundant power: $20 to $40 per sq ft
  • Data center or high-density industrial: $35 to $70+ per sq ft

Copper pricing swings can shift these ranges quickly. Current material pricing matters more in electrical than almost any other trade.

What to Send for an Electrical Takeoff

Send complete documents to get the tightest possible number. Missing schedules force assumptions.

  • Single-line diagrams and panel schedules
  • Lighting and power plans with device locations
  • Fire alarm and low-voltage drawings if applicable
  • Specification sections for gear and fixture quality basis

Electrical Takeoff Mistakes That Cost Bids

A few habits cause most electrical takeoff errors. Watch for these on your next bid.

  • Skipping the circuit-by-circuit reconciliation against the panel schedule
  • Estimating homerun length instead of measuring actual routing
  • Averaging device labor across all receptacle types
  • Missing voltage drop calculations on long feeder runs

A full takeoff is only one part of the bid. See our commercial electrical estimating guide for pricing benchmarks by system.

Fire Alarm and Life Safety Circuits in an Electrical Takeoff

Fire alarm devices and life safety circuits often get bundled into a general electrical takeoff. They deserve their own line items instead.

Initiating devices, notification appliances, and control panel wiring each carry distinct labor units. Treating them like standard branch circuits misprices this scope.

  • Smoke detectors, pull stations, and heat detectors
  • Horn/strobe and speaker notification devices
  • Fire alarm control panel wiring and programming
  • Emergency lighting tied to the life safety system

Electrical Takeoff Turnaround by Project Size

Turnaround depends on drawing completeness and project size, not just square footage. A clean, complete set moves faster regardless of size.

  • Small tenant improvement: same-day to 24 hours with complete drawings
  • Mid-size commercial project: 24 to 48 hours standard
  • Large or complex projects with multiple buildings: 48 to 72 hours

How We Run an Electrical Takeoff

Our electrical takeoff service reconciles every circuit against the panel schedule before pricing. We separate gear, conduit, wire, and devices into clear line items.

Frequently Asked Questions

What is included in an electrical takeoff?

A complete electrical takeoff includes conduit footage, wire footage, panel and gear schedules, and device counts by type. Everything is cross-checked against the panel schedule. Fire alarm and low-voltage devices are counted separately.

Why does the panel schedule matter in a takeoff?

The panel schedule confirms circuit count and breaker sizing. It catches discrepancies between the floor plan and the actual electrical design before they become field problems. Revised schedules should always be checked against the latest addenda.

How do you count switchgear separately from branch wiring?

Switchgear, panelboards, and transformers are scheduled with voltage, ampacity, and AIC rating noted. This separates long-lead gear pricing from bulk conduit and wire material. Lead times on large gear can exceed several months.

How fast can I get an electrical takeoff back?

Most commercial electrical takeoffs come back in 24-48 hours with a complete drawing set. Larger multi-building projects can take longer. Learn more about our electrical estimating services.

Ready for a takeoff your crew can bid from with confidence? Request an estimate and get results in 24-48 hours.

Topics

electrical takeoffelectrical estimatingpanel scheduleconduit takeoffcommercial electricaltakeoff checklist

Stop Losing Bids to Inaccurate Estimates

Our certified estimators deliver professional MEP cost estimates, with most delivered within 24-48 hours. All trades, all project types.